Translate

2022年12月30日星期五

Caterpillar Excavator Bolted Flag Removal Procedure and Installation Procedure

                   cat 325FLExcavator  Bolted Flag RemovalProcedure and Installation Procedure


Caterpillar CAT Factory Password Calculator Generator 10 Digits VM Version


                                 WARNING!
Failure to follow the instruction below for the installation of a work tool may result in personal injury or death. Special care must be taken if more
than one person is installing the work tool. Confirm the verbal communication and the
hand signals that will be used during the
installation.

 Be alert for sudden movement of the front linkage and the work tool.

 Do not insert fingers into the bores of the support pins when the support pins and the bores
are being aligned.
NOTICE
To facilitate removal of the bucket pins without causing damage to the pins, the bearings, and/or the Oring seals put the bucket on the floor and the stick in
a vertical position, as shown.
Removal Procedure


10.2021 Caterpillar SIS EPC+Service Manual download & Full Installation Service


1. Start the engine. Park the machine on a hard, level
surface. Position the bucket, the stick, and the
bucket control linkage, as shown. Shut off the
engine.


2. Slide O-ring seals (6) off the pin joints and onto the
flanges of the bucket.

        WARNING!
When the pin assembly is removed, the linkage
assembly may swing out of the bucket. To prevent possible personal injury, do not stand in
front of the linkage assembly when the pin assembly is being removed.
Note: Removing the support pin may be difficult due
to excessive pressure on the support pin. Remove
the pressure on the support pin by adjusting the front
linkag

3. Remove bolt (7). Remove support pin (8).
4. Remove bolt (10). Remove support pin (9).
5. Start the engine and raise the stick out of the
bucket.
6. Remove the O-ring seals (6) from the flanges on
the bucket
Note: After the support pins have been removed,
make sure that the support pins do not become
contaminated with sand or dirt. Make sure that the
seals on the end of the stick and the seals on the end
of the link do not become damaged.


Caterpillar Hydraulic Information System (HIS)


Installation Procedure
1. Clean each pin and each pin bore. Lubricate each
pin bore with molybdenum grease.




2.PositiontheO-ringseals(6)ontotheflangesofthebucket
Illustration289g03822736

 

3.Starttheengineandlowerthestickintothebucketuntilthepinboresareinalignmentwitheach other.Stoptheengine.
4.Installsupportpin(9)intothepinbore.
5.Installbolt(10)
6.RefertoOperationandMaintenanceManual,“BucketLinkage-Inspect/Adjust”inordertoadjust thebucketclearance.
7.SlideO-ringseals(6)inpositionoverthepinjointsbetweenthebucketandthestick.
8.Starttheengineandpositionthebucketlinkageintothebucketuntilthepinboresareinalignment witheachother.Stoptheengine.
9.Installsupportpin(8)intothepinbore.

2019 Caterpillar Lift Trucks MCFE/MCFA/MCFS EPC+Service All in One VM Version

10.InstallBolt(7).
11.SlidetheO-ringseals(6)overthepinjointsbetweenthebucketandthelinkassembly.
12.Lubricatethebucketpins.RefertoOperationandMaintenanceManual,“BucketLinkage-Lubricate”orOperationandMaintenanceManual,“Boom,
Stick,andBucketLinkage-Lubricate”.

312D2 and 313D2 Excavators, Machine Systems Duo-Cone Universal Floating Seal - Installation

  This article describes the 312D2 and 313D2 excavators, machine systems Duo-Cone Universal Floating Seal - Installation Caterpillar ET2024...